Difference between revisions of "Rfid-breakout"
From SB-Components Wiki
(→Pinout) |
(→Pinout) |
||
| Line 30: | Line 30: | ||
<tr> <td> VCC </td> <td> Connect to 5V of Power supply. </td> </tr> | <tr> <td> VCC </td> <td> Connect to 5V of Power supply. </td> </tr> | ||
| − | <tr> <td> GND /td> <td> Connect to ground </td> </tr> | + | <tr> <td> GND </td> <td> Connect to ground </td> </tr> |
<tr> <td> BEEP </td> <td> Connect to Buzzer, Goes high on detection of card </td> </tr> | <tr> <td> BEEP </td> <td> Connect to Buzzer, Goes high on detection of card </td> </tr> | ||
<tr> <td> SEL </td> <td> SEL=1 then o/p =RS232, SEL=0 then o/p=WEIGAND </td></tr> | <tr> <td> SEL </td> <td> SEL=1 then o/p =RS232, SEL=0 then o/p=WEIGAND </td></tr> | ||
| − | <tr> <td> DATA /td> <td> Transmit pin for RS232 Communication </td></tr> | + | <tr> <td> DATA </td> <td> Transmit pin for RS232 Communication </td></tr> |
<tr> <td> D0 </td> <td> WEIGAND interface DATA HIGH pin </td></tr> | <tr> <td> D0 </td> <td> WEIGAND interface DATA HIGH pin </td></tr> | ||
<tr> <td> D1 </td> <td> WEIGAND interface DATA LOW pin </td></tr> | <tr> <td> D1 </td> <td> WEIGAND interface DATA LOW pin </td></tr> | ||
Latest revision as of 10:36, 25 June 2021
RFID Breakout
RFID Breakout is an updated UART/USB 2.0 interface running at the frequency of 125KHz with a compact design that is compatible with all the variants of Raspberry Pi, Arduino, STM32, PIC, AVR, Beaglebone, etc.
The operating voltage of the RFID breakout is +4.5V to +5.5V(DC). The consumption of the current for RFID breakout is 50mA. It runs at the operating temperature of 0ºC to 80ºC. On the serial line, the baud rate of RFID is efficient, that is 9600 bps.
Features
- Supports all Raspberry Pi, Arduino, STM32, PIC, ARM, AVR, Beaglebone, etc.
- Comes with Development resources and manual
- Supports 125kHz Key Fob/ Tags.
- UART (Serial) / USB 2.0 Interface
- Current Consumption is 50mA.
Specifications
- Operating Voltage - +4.5V to +5.5V(DC)
- Operating Frequency - 125kHz
- Communication Interface - UART (Serial) / USB 2.0
- Default baud rate - 9600 bps
Buy it From : Click Here
Pinout
| Pinout | Description |
|---|---|
| VCC | Connect to 5V of Power supply. |
| GND | Connect to ground |
| BEEP | Connect to Buzzer, Goes high on detection of card |
| SEL | SEL=1 then o/p =RS232, SEL=0 then o/p=WEIGAND |
| DATA | Transmit pin for RS232 Communication |
| D0 | WEIGAND interface DATA HIGH pin |
| D1 | WEIGAND interface DATA LOW pin |
Installation
Arduino
- Connect RFID breakout with Arduino uno as shown below :
 |
|
- Now visit the below link for Arduino source code.
https://github.com/sbcshop/RFID-Breakout/blob/main/Arduino/rfid_read/rfid_read.ino
Raspberry Pi
Connect RFID breakout with Raspberry Pi as shown below :
 |
|
- Now visit the below link for Raspberry Pi source code.
https://github.com/sbcshop/RFID-Breakout/blob/main/Python/rfid_read.py
Resources
Github