Difference between revisions of "Pico-2g-expansion"
From SB-Components Wiki
| Line 63: | Line 63: | ||
* Insert SIM card on SIM card slot, and connect GSM and GSM Antenna on antenna connector. | * Insert SIM card on SIM card slot, and connect GSM and GSM Antenna on antenna connector. | ||
* Connect USB on the USB port of Pico 2G GSM board. | * Connect USB on the USB port of Pico 2G GSM board. | ||
| + | * Press and hold '''PWR_KEY''' to turn on the GSM module (SIM868) and release it once '''STATUS''' led turned on. | ||
* Now open any Serial terminal app on (Windows or Linux), Set com port of Pico 2G expansion and baud rate to 9600. | * Now open any Serial terminal app on (Windows or Linux), Set com port of Pico 2G expansion and baud rate to 9600. | ||
| − | |||
==== MicroPython ==== | ==== MicroPython ==== | ||
Revision as of 06:52, 27 September 2021
Pico 2G Expansion (Incomplete Wiki)
Raspberry Pi Pico 2G Expansion is a QUAD-Band GSM/GPRS/GNSS Expansion designed dedicatedly for Raspberry Pi Pico with UART, USB 2.0 Interface, 850/900/1800/1900 MHz, Bluetooth 3.0 based on SIM868 module to perform easy and efficient communication. Pico 2G Expansion works on the embedded TCP/UDP Protocols with Multi-constellation GNSS receiver support.
Pico 2G Expansion also includes a 1.14-inch display with a resolution of 240 x 135 pixels, 65K RGB colors, and a sharp and vivid exhibiting effect, designed primarily for user engagement via SPI connection by incorporating a GPIO header. The 1.14-inch LCD includes the ST7789 Driver and SPI Interface, decreasing the amount of IO pins required.
Features
- 1.14” LCD
- Low Power Consumption
- 850/900/1800/1900 MHz Frequency band
- Bluetooth 3.0
- LED Indicators
- Serial/USB/SIM868 Selection Jumpers
Specifications
- Operating Voltage - 5V(via USB)
- Communication - UART/USB 2.0
- SIM Module - SIM868
- Compatibility - Raspberry Pi Pico
- Operating Temperature - -400 ~ 800 C
- Dimensions - 68 x 119.64 mm
File:Pico 2g expansion.png
Buy it From : Click Here
Pinout
| PICO 2G Board | PICO Pins |
|---|---|
| VCC | 5V |
| GND | GND |
| LCD DIN | GP11 |
| LCD CLK | GP10 |
| LCD DC | GP8 |
| LCD CS | GP9 |
| LCD RST | GP12 |
| LCD BL | GP13 |
| SIM868 PWRKEY | GP22 |
| SIM868 TX | GP1 |
| SIM868 RX | GP0 |
Jumper Selection
| SIM868 Operation (Device Selection) | 400 px | ||
|---|---|---|---|
| Jumpers 1 | Jumper 2 | MODE | |
| Short P_TX - U_RX | Short P_RX - U_TX | Pico to USB Communication | |
| Short U_RX - S_RX | Short U_TX - S_TX | USB to SIM868 Communication | |
| Short P_TX - S_RX | Short P_RX - S_TX | SIM868 to Pico Communication | |
| Open | Open | No Communication | |
Installation
USB to SIM868 Communication
- Connect Selection jumpers for USB to SIM868 communication mode.
- Insert SIM card on SIM card slot, and connect GSM and GSM Antenna on antenna connector.
- Connect USB on the USB port of Pico 2G GSM board.
- Press and hold PWR_KEY to turn on the GSM module (SIM868) and release it once STATUS led turned on.
- Now open any Serial terminal app on (Windows or Linux), Set com port of Pico 2G expansion and baud rate to 9600.
MicroPython
Resources
- 'Software
- Github