Difference between revisions of "Home-Automation-HAT"
From SB-Components Wiki
| Line 39: | Line 39: | ||
== Installation == | == Installation == | ||
| − | ==== Raspberry Pi (Using PiRelay | + | ==== Raspberry Pi (Using PiRelay App) ==== |
PiRelay is an Android app you can use to Switch or Pulse the GPIO Pins of a Raspberry Pi connected to Relays. To use this app you will need to setup your Raspberry Pi and Relays. | PiRelay is an Android app you can use to Switch or Pulse the GPIO Pins of a Raspberry Pi connected to Relays. To use this app you will need to setup your Raspberry Pi and Relays. | ||
App Download link: | App Download link: | ||
| − | * To setup PiRelay on Raspberry Pi, run the below | + | * To setup PiRelay on Raspberry Pi, run the below commands one by one. Must complete all commands to make it work with Raspberry Pi. |
'''Commands to Install: WiringPi, Apache, PHP & Download the GPIO PHP File''' | '''Commands to Install: WiringPi, Apache, PHP & Download the GPIO PHP File''' | ||
| + | |||
| + | <source lang="shell"> sudo apt-get update </source> | ||
| + | <source lang="shell"> sudo apt-get install wiringpi apache2 libapache2-mod-php -y </source> | ||
| + | <source lang="shell"> sudo wget https://pirelay.jasonfindlay.com/downloads/gpio.dl </source> | ||
| + | <source lang="shell"> sudo mv gpio.dl /var/www/html/gpio.php </source> | ||
== Resources == | == Resources == | ||
Revision as of 05:48, 28 September 2021
Home Automation HAT
Home Automation HAT is a Home monitoring and automation controller HAT for the Raspberry Pi that can control up to 2 appliances/devices on a load of 250 VAC/7A, 30 VDC/10A, photo-coupling isolation Optocoupler EL357NC, allowing users to safely control high voltages or current devices. Home-Automation HAT makes appliances smart, which users can operate via the PiRelay app on their electronic device.
Features
- Compatible with Raspberry Pi 4, 3B+,3,2,Zero
- Relay Status Indicator
- Comes With Development Resources, including examples in Python
- COM, NO(Normally Open) & NC(Normally Closed) are available for each relay
- Connectivity of Relay With RPi Without GPIO
- Connectivity Using Stack Method
- Onboard Power LED Indicator
- Make Your Home IoT Enabled
- Relay Control Pins Selection Jumper
Specifications
- Operating Voltage - 220V AC (Via Terminal Block)
- External Load - 250 VAC/7A, 30 VDC/10A
- Relay Channels - 2
- Trigger Signal - 3.3/5V
- Optocoupler - (CTR: 50~600% at IF= 5mA, VCE = 5V)
- External Power Supply - Via Terminal Block
- GPIO - 40 Pins Stacking Header
- Load Connector - Screw Terminal Block for each Relay(Output)
File:Home-auto-hat.png
Buy it From : [ Click Here]
Pinout
| Relays | BOARD | BCM |
|---|---|---|
| Relay 1 | 35 | GPIO 19 |
| Relay 2 | 33 | GPIO 13 |
Installation
Raspberry Pi (Using PiRelay App)
PiRelay is an Android app you can use to Switch or Pulse the GPIO Pins of a Raspberry Pi connected to Relays. To use this app you will need to setup your Raspberry Pi and Relays. App Download link:
- To setup PiRelay on Raspberry Pi, run the below commands one by one. Must complete all commands to make it work with Raspberry Pi.
Commands to Install: WiringPi, Apache, PHP & Download the GPIO PHP File
sudo apt-get update
sudo apt-get install wiringpi apache2 libapache2-mod-php -y
sudo wget https://pirelay.jasonfindlay.com/downloads/gpio.dl
sudo mv gpio.dl /var/www/html/gpio.php
Resources
Github