Difference between revisions of "Home-Automation-HAT"

Revision as of 11:43, 21 October 2021

Home Automation HAT

Home Automation HAT is a Home monitoring and automation controller HAT for the Raspberry Pi that can control up to 2 appliances/devices on a load of 250 VAC/7A, 30 VDC/10A, photo-coupling isolation Optocoupler EL357NC, allowing users to safely control high voltages or current devices. Home-Automation HAT makes appliances smart, which users can operate via the PiRelay app on their electronic device.

Features

Compatible with Raspberry Pi 4, 3B+,3,2,Zero
Relay Status Indicator
Comes With Development Resources, including examples in Python
COM, NO(Normally Open) & NC(Normally Closed) are available for each relay
Connectivity of Relay With RPi Without GPIO
Connectivity Using Stack Method
Onboard Power LED Indicator
Make Your Home IoT Enabled
Relay Control Pins Selection Jumper

Specifications

Operating Voltage - 220V AC (Via Terminal Block)
External Load - 250 VAC/7A, 30 VDC/10A
Relay Channels - 2
Trigger Signal - 3.3/5V
Optocoupler - (CTR: 50~600% at IF= 5mA, VCE = 5V)
External Power Supply - Via Terminal Block
GPIO - 40 Pins Stacking Header
Load Connector - Screw Terminal Block for each Relay(Output)

Buy it From : Click Here

Pinout

Relays	BOARD	BCM	Wiring Pi
Relay 1	35	GPIO 19	24
Relay 2	33	GPIO 13	23

Installation

CAUTION: Be careful when working with the electrical product. Special supervision of parent/adult is required to keep children from hurting themselves.

Raspberry Pi (Using PiRelay App)

PiRelay is an Android app you can use to Switch or Pulse the GPIO Pins of a Raspberry Pi connected to Relays. To use this app you will need to setup your Raspberry Pi and Relays. App Download link: https://play.google.com/store/apps/details?id=com.jasonfindlay.pirelaypro

To setup PiRelay on Raspberry Pi, run the below commands one by one. Must complete all commands to make it work with Raspberry Pi.

Commands to Install: WiringPi, Apache, PHP & Download the GPIO PHP File

sudo apt-get update

sudo apt-get install wiringpi apache2 libapache2-mod-php -y

sudo wget https://pirelay.jasonfindlay.com/downloads/gpio.dl

sudo mv gpio.dl /var/www/html/gpio.php

Setting Up Your Android Device

Download Pi Relay app from the Play Store here: PiRelay App Download

Make sure your Pi and Android Device are on the same network. Then in the app settings, you can define a custom Server URL. This is the network path to your Raspberry Pi. The default path is " http://raspberrypi/ ", however, you can define an IP address or a custom URL. To set up communication with your Raspberry Pi, click on ≡ >> Pi URL Addresses, then set Pi 1 : Your Pi IP Address (for eg: http://192.168.1.14)
To turn on/off relays, Use Pins as Wiring Pi pinout shown above in Pinout table.
To setup Relays, Click on ≡ >> Number of Relays, and set it to 2.
Now again click on ≡ >> Setup Relays, Now click on any relay and set WiringPi Pin for Relay 1 as 24, and Relay 2 as 23. You can also set Relay default status here.
Now move back to the home screen and click on On/Off button to turn on/off relays.

Raspberry Pi (Using Python)

Resources

Github

Source Code

@@ Line 61: / Line 61: @@
 [[File:PiRelay-APP.PNG | 600px]]
-* Make sure your Pi and Android Device are on the same network. Then in the app settings, you can define a custom Server URL. This is the network path to your Raspberry Pi. The default path is " http://raspberrypi/ ", however, you can define an IP address or a custom URL. To setup communication with your Raspberry Pi, click on '''≡ >> Pi URL Addresses''', then set Pi 1 : Your Pi IP Address (for eg: http://192.168.1.14)
+* Make sure your Pi and Android Device are on the same network. Then in the app settings, you can define a custom Server URL. This is the network path to your Raspberry Pi. The default path is " http://raspberrypi/ ", however, you can define an IP address or a custom URL. To set up communication with your Raspberry Pi, click on '''≡ >> Pi URL Addresses''', then set Pi 1 : Your Pi IP Address (for eg: http://192.168.1.14)
 * To turn on/off relays, Use Pins as Wiring Pi pinout shown above in Pinout table.
 * To setup Relays, Click on '''≡ >> Number of Relays''', and set it to 2.
 * Now again click on '''≡ >> Setup Relays''', Now click on any relay and set WiringPi Pin for '''Relay 1 as 24''', and '''Relay 2 as 23'''. You can also set Relay default status here.
 * Now move back to the home screen and click on On/Off button to turn on/off relays.
+==== Raspberry Pi (Using Python) ====
 == Resources ==